Discovering Essential Plumbing Skills is Crucial For Installing a Bathtub
Discovering Essential Plumbing Skills is Crucial For Installing a Bathtub
Blog Article
What are your thoughts about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Installing a bath tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a brand-new one is also a moderately tough project. If the old tub is easily obtainable, the project can move easily; if you need to open a wall surface to get rid of the old bathtub as well as place the brand-new tub, the task is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as embeded in the new one. Make sure you have qualified yourself for the work and fit trying it. Rather than working with a specialist to take control of a halfway-completed task, it is better to think about utilizing one before you start. Possibilities are you may need an expert plumber to make tube links.
This write-up will help you mount a brand-new bathtub in your bathroom if you have actually already gotten a new tub and also don't require to alter the setup of your previous supply of water pipes.
Your devices and also product list ought to make up the following:
Planning for the Installation
First of all, the supporting frame provided with the bathroom needs to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps utilizing 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently prepare to be suited its final setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be rather troublesome as a result of the limited gain access to that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before moving on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Bathtub
Using both wood boards under its feet, position the bathtub in the needed placement. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The following goal is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bathtub until the level checks out level.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply as well as check all joints as well as new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bath paneling as described in the manufacturer's user's manual. Tiling and sealing around the tub must wait until the tub has actually been used at the very least when as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area between the faucet and also the sink. Safeguard the faucet in position with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The former kind ought to be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall in between the bath and the tiling, leading to problems with wetness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes and cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to allow for the activity experienced when the tub remains in usage. The sealant can split relatively early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently available on the market. It is a good idea to fit the floor tiles utilizing water-resistant or water-proof glue and cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

As an enthusiastic person who reads on How to Install a Bathtub, I assumed sharing that excerpt was a smart idea. Liked our post? Please share it. Let other people find it. Thanks a lot for taking the time to read it.
Certified experts available. Report this page